Do-It-Yourself Wedding Projects

I am completely smitten with these coat check tags…adding a bit of whimsy and personality into the most unexpected place…

How to make Coat Check Tags…

I designed the template myself and printed them out at home on Crane’s 179 lb. Pearl White Cover (www.crane.com). I trimmed each one out using an x-acto and ruler. Then, using Fiskars 1/8″ hole punch I made a hole to place the eyelet. Before adding the eyelet I scored each card so that the ticket could be torn evenly. To do this I used the Fiskars Rotary Paper Trimmer with the Perforating Blade (www.fiskarscrafts.com). Then the 1/8″ eyelet t is added by hammering it with a setter (www.impressrubberstamps.com).

Download the templates here and here!

***

These hair pins are drop dead gorgeous. Romantic, ethereal and subtle…they would be the perfect addition to any gown…

Flower Hair Pin Instructions from Thryn…

The materials I used to make my hair pins were as follows:

scraps of silk, both sheer and opaque

small pearl beads

wired pearl beads (these have a pearl drop at each end of a short piece of white-wrapped wire)

clear plastic hair comb

silver hairpins (that look like big bobby pins) with a flat piece at the top for attaching something

wired bridal florals (or whatever other color/style of additional pieces you want to add to the fascinator–wired is best since it keeps it flexible)

hot glue gun

To make the flowers, I cut first small petal shapes out of the silk.

For the large flower, I cut them in three different sizes, and used about 5-6 petals for each layer. For the small flowers, I used 5 petals for each that were all the same size.

Make a gathering stitch at the bottom of each petal, pull it tight and tie a knot to give the petal some dimension.

Then, overlap 5 or 6 petals at their bottoms, and sew straight up through the center, making sure the stitch goes through all 5 petals. Sew a few stitches to secure the petals in place. Lay another layer of petals on top of the bottom layer in the same formation, and sew through the center again. Keep adding layers of smaller petals until the flower is the desired size. I used three layers of opaque petals, and then added 1 or two layers of sheer petals on the very top. It will obviously get more difficult to sew through the layers as you keep adding more, but just push it straight through and be careful not to break the needle.

To finish the flower, I glued three small pearl beads to the center of the flower to cover up the stitches. Then I took two of the wired pearl beads and bent each one in half so it looked like this:

I glued them to the center so the pearl drops stick out from the center of the flower.

Once the large flower is complete, it’s time to assemble the fascinator. This excellent online guide by Corvus Tristus explains the basics for making a fascinator and was extremely helpful. In my case, I had a wired bridal floral piece that was leftover from my older sister’s wedding that I placed behind the flower. The wired piece was key since I didn’t know in what direction the comb would be facing when my hairdresser attached it to my head. So she was able to put the comb in my hair, and then move the flower piece around so it was facing the right direction.

To make the small flowers, follow the same directions as you would to make one layer of petals of the big flower (overlap the petals at the center and sew through). Glue three small pearls to the center to cover up the stitches, and glue to the flat part of the silver pin.

In total, it’s about an evening’s work to make a large flower and four small flowers. I hope this guide is helpful!

To see images that coordinate with the instructions, check out Thryn’s website.

***

The flower top favor boxes that this reader designed and created look absolutely professional. Based on a modified template she found online, these boxes fold from a single sheet of paper without glue…

Instructions for Flower Top Favor Boxes from Thryn…

This favor box template is fairly easy to modify to whatever size you need the boxes to be. The ones I made are 2.75″ x 2.75″. The top part could be cut out in any shape that is semi-curcular. It might also look nice to just use scalloped scissors to cut out the half-circles for a variation. It would also be pretty to trace the template onto pretty handmade paper. I find that coverstock works the best, but I printed my tests onto text paper and the boxes still held up. The thinner paper just made them a little less durable. To get the template, check Thryn’s website!

***

These beautiful olive branch inspired invitations and favors are about as close to perfect as you can get. They are elegant, soft and seem so personal.

Instructions on Making the Olive Branch Details…

I designed the wedding invitation using Adobe Illustrator. Then, my dad printed the invitations for me on an off-set lithography press using a medium gray ink. I hand-stamped each one with the Olive Branch using a “Soft Celery” colored archival ink pad. I even stamped the outside of the envelope next to the addressee’s name.

On the wedding day, guests received programs with the familiar stamp on the cover. The program was also designed using Adobe Illustrator and was printed in a medium gray ink.

At the end of the reception, guests picked up a small glassine envelope which was filled with birdseed and sealed with sewing thread and a slip of paper stamped with the olive branch. These were all handmade by me the week before the wedding! I used my sewing machine set on the zig-zag stitch to sew through the layers. It was simple for the guests to rip them open when the time came to toss the birdseed at the bride and groom.